Technical Tips

Technical info not specific to a particular mfr.
Respond to existing topics with questions or comments.
User avatar
4Strokes
Site Admin
Posts: 1238
Joined: May 02, 2016

Technical Tips

Postby 4Strokes » Sun Jun 19, 2016 6:21 pm

Airbox Sealing
Seal off the small openings and seams at the rear fender, sub-frame and air-box junctions with Silicone type sealant to prevent mud and water from entering the air intake system. -4Strokes.com

Brake/Clutch Perch Mod
Never snap or bend a lever again! Remove the clutch and brake perches and wrap the handlebar with a couple wraps of Teflon (pipe) tape. Remount the perch and tighten lightly but not too tight. You should be able to adjust the lever angle with just your hand. -4Strokes.com

Cable Lube/Oiler
Lewis recommends getting a hold of a doctors syringe. Fill with light oil, similar to sewing machine oil. Disconnect the lever and cable. Insert the tip of the syringe into the end of the cable housing and squeeze the syringe to oil the cable. Continue until the lever feels loose and free. -Lewis Griffiths

Carburetor Screw Replacement
Replace the screws for the carburetor float bowl with allen-head screws. It's easier to get an allen wrench under the carburetor and less likely to round out the head of the screw. -4Strokes.com

Fix Fatigue Lines in Plastic
You can use a heat gun to fix the fatigue lines that you get in plastic when it has been folded or bent over. Just run a heat gun over the fatigue line/s until they disappear. Be careful not to overheat and melt the plastic. -Dirt Rider Magazine

Fork Oil Level
Forks are sensitive to oil level height. A 2mm change in either direction can be felt. Increase the level to make the forks more resistant to bottoming and decrease the level to cushion the ride more. -4Strokes.com

How to Add Fork Oil
Take the weight off the forks, remove fork caps, add oil as needed, and reinstall caps. Don't forget to bleed the air out of the forks when the bike is back on the ground. If further adjustment is necessary, use heavier or lighter oil. -4Strokes.com

Frame Protection
When installing frame guards place a piece of Rhino Guard or Fox Clear Force Field (thick clear plastic decal) to the area underneath the guard to prevent scraping. You can also use Rhino Guard for other areas that require protection. -MotoLappa

Grease Swing-arm, Linkage Pivots & Headset
Grease the swing-arm, linkage pivot points, and the headset bearings on a regular basis. Use any good high-temp wheel bearing grease and make it a routine service. -4Strokes.com

Grip Glue Alternative
Mike uses golf club grip tape and solvent and says it works great! The grip tape gets slimy when wet with solvent and after it dries you have to cut the grip off to replace it. -Mike Walley

Grip Removal
Insert a small diameter long blade screwdriver between the grip and bar. Then insert the tube from a can of WD40 in along with the of the screwdriver. A squirt of WD40 and a little twist of the screwdriver and the grip will easily twist off the bar. -William Faulk

Grip Replacement
When replacing grips, I use an opened coat hanger between the grip and bar to loosen the old glue. A hook on the inserted wire end draws the grip off when pulled. Hair spray allows the new grips to slide right on while keeping them in place when it dries. -James Meehan

Handlebar Sealing
Seal the right side of the handlebar with silicone sealant to prevent dirt from fouling the throttle tube's action due to a left-side crash. -American Honda

Headset Bearing Free-Play
To check headset bearing free-play, apply the front brake and rock the bike back and forth with your finger against the frame and the edge of the top headset seal or bearing race. If the headset is loose you will feel it with your finger. -4Strokes.com

Leaky Fork Seals
If your fork seals just started leaking, you might want to try sliding a playing card or the like up under the seal and spin it around the fork leg. Sometimes it may dislodge a particle that is keeping the seal from sealing. -4Strokes.com

Mileage Tracker
Kricho uses plastic tie-wraps attached to the handlebars between the triple-clamps, keeping with a size and color scheme, I alternate red and black, narrow and wide, to track total mileage of the bike. -Kricho

Plastic Mud Repellant
Before going riding, Bruce sprays the underneath side of his fenders with non-stick cooking spray. He says the mud just falls off when when hit with the spray from a garden hose. No more pressure washer! -Bruce

Rear Wheel Adjusters
Always run the rear wheel adjuster as far forward as possible. In this position the chassis gives better traction, is more precise in corners and lifts the front wheel more easily when necessary. -4Strokes.com

Speedometer/Odometer/Computer
You can install a simple mountain bike computer on your dirt bike with little effort and have an accurate speedometer for less than $40. It also keeps track of total mileage and time. -Glenn Ulrich

Spokes & Spoke Tightness
Keep an eye on your spokes, especially the rear. Buy a spoke or spoke torque wrench. If you constantly have problems braking spokes, look into swapping them out for aftermarket or larger diameter spokes. -4Strokes.com

Return to “Non-Mfr Technical Reference”

Who is online

Users browsing this forum: No registered users and 1 guest